How Many Holes a Day Can a Tractor Post Hole Digger Dig? Output by Soil Type and Cost per Hole
Fifty seconds. That's how long it takes a tractor post hole digger to punch a hole into decent soil, start to finish. On its own, that number is almost useless; it tells you nothing about what you'll actually get done between 8 a.m. and sundown on a fence line with mixed clay and the odd buried rock. Ashok Metal Works has built these augers for 25+ years, and the gap between "cutting time" and "daily output" is the single most common mistake contractors make when pricing a job. This post walks through both numbers honestly: what the digger actually does, and what a hole actually costs you once reality gets involved.

⏱️ The Real Spec: 50 Seconds, 7 Feet Deep, and What the Diameter Actually Is
In favourable soil, the Ashok Metal Works post hole digger cuts a standard hole in about 50 seconds and can go as deep as 7 feet, with a diameter of 18 inches (can be customised according to the customer's requirements). Augers aren't one-size-fits-all; confirm the exact diameter you need when you place the order, since it's one of the easiest specs to tailor to the job.
What stays consistent across the range: this is a rear-mounted, PTO or hydraulically driven implement, runs off a 3-point hitch, and it's built to dig, not to excavate rock.
🪨 "Small Rocks Are Fine, Big Rocks Aren't" — What That Actually Means
This line gets said a lot, and it deserves an explanation instead of a shrug. An auger's flighting and cutting edge are designed to shear and lift soil, and gravel or small embedded stones mostly just get caught up in that same motion and carried out with the spoil. A buried rock the size of a football is a different problem entirely; the auger doesn't cut it, it stalls against it, and depending on how the drivetrain is set up, that's either a sheared pin (by design, to protect the gearbox) or a bent blade if you keep forcing it. Ashok Metal Works' own guidance on this line is to run hydraulic-drive models for rocky or clay-heavy ground, where you get downforce to push through resistance instead of relying on tractor PTO torque alone and to skip digging altogether in soil that's gone bone dry or turned to soup, since neither condition behaves the way the auger expects.
📊 Tractor Post Hole Digger Output by Soil Type
Here's where the 50-second number and your actual daily count diverge. Cutting time is only part of the cycle; you're also repositioning the tractor, raising and lowering the hitch, clearing spoil off the flighting (worse in wet clay, where it packs instead of falling away), and lining up the next hole. None of that is published anywhere as an official figure, so treat the table below as a working estimate to test against your own site, not a guaranteed output chart:
Soil Type | Typical Cycle Time (incl. repositioning) | Realistic Holes in an 8-Hour Day |
Sandy / loose soil | ~2.5–3 min | 140–160 |
Loamy / average soil | ~3.5–4 min | 100–120 |
Dry clay | ~4.5–5.5 min | 75–95 |
Wet or compacted clay | ~6–8 min | 50–65 |
Soil with small embedded rocks | ~5–7 min | 55–75 |
Large rocks or buried boulders | — | Not recommended for this auger |
Two things worth flagging about that table. First, it assumes a halfway competent operator who isn't stopping every third hole to clear a jam; a sharp, well-matched auger (blade versus bit, depending on soil) closes a lot of that gap. Second, real fence lines rarely sit in one soil type for their whole length, so your actual day usually lands somewhere between rows, not neatly on one.
💰 What a Tractor Post Hole Digger Actually Costs Per Hole
Cost per hole isn't one number; it's diesel, labour, and (if you want to be precise about it) a sliver of the attachment's purchase price spread across its working life. The formula is simple enough to run yourself:
Cost per hole = (fuel cost per hour + labour cost per hour) ÷ holes per hour
Below is a worked example using placeholder rates; swap in your actual diesel price and crew wage, because these vary enough by region that a single published number would be more misleading than helpful:
Input (example only) | Assumed Value |
Diesel price | ₹95/litre |
Tractor fuel burn under PTO load | ~3.5 L/hour |
Fuel cost per hour | ~₹330 |
Operator/labor cost per hour | ~₹50 |
Combined hourly cost | ~₹380 |
At that hourly cost, loamy soil running 15–17 holes/hour works out to roughly ₹22–25 per hole. Drop into wet clay at 8–10 holes/hour and the same ₹380/hour climbs to ₹38–48 per hole, not because the digger got worse, but because you're spreading the same fixed hourly cost across fewer holes. That's the real argument for matching the right drive type (PTO versus hydraulic) and auger style to your ground before the job starts, rather than after you've already burned a day fighting it.
🔧 Getting Closer to the 50-Second Number in the Field
A few things actually move the needle between the spec-sheet number and what you get on site:
Mark hole locations ahead of time instead of eyeballing them hole-by-hole; cuts repositioning time more than almost anything else on this list
Match blade-style augers to clean soil and bit-style augers to tougher, mixed ground; using the wrong one is a common reason output drops
Keep PTO speed in the recommended range; running too fast doesn't cut faster, it just burns up the cutting edge
Pair the implement with a tractor rated at 45+ PTO HP, and if you're also running a pole erector, look for 2000 kg+ hydraulic lift capacity; underpowered tractors stall more than they dig
Switch to a hydraulic-drive model with downforce if your ground is consistently clay-heavy or has scattered small rock; fighting it with a standard PTO unit all season costs more in time than the upgrade would
⚠️ When This Isn't the Right Tool
Large buried rock fields, bedrock close to the surface, and ground that's recently flooded are all situations where this auger either can't do the job or will cost you more in broken pins and bent blades than it's worth. It's also worth knowing that striking a rock hard enough to bend a blade or crack a housing is physical damage, not a hydraulic component failure, so it sits outside what the standard 1-year hydraulic warranty (hoses, control valve, cylinder) actually covers. If a site has rock you can't see from the surface, a quick probe or a conversation with Ashok Metal Works about hydraulic downforce models before you commit is cheaper than finding out mid-job.
Frequently Asked Questions
Q: How many holes can a tractor post hole digger dig in a day?
A: In good soil, realistically 100–160 holes across an 8-hour day once you account for repositioning and spoil clearing, not just the 50-second cutting time per hole. In heavy clay or ground with small rocks, that drops to roughly 50–75.
Q: How fast does the Ashok Metal Works post hole digger actually cut a hole?
A: About 50 seconds in favourable soil conditions, confirmed for this product line.
Q: What's the maximum digging depth and diameter?
A: Up to 7 feet deep, with a diameter of 18 inches (can be customised according to the customer's requirements).
Q: Can it dig through rocky soil?
A: It handles soil with small embedded rocks without trouble. Larger buried rocks will stall or damage the auger rather than get cut through in consistently rocky or clay-heavy ground; a hydraulic-drive model with downforce is the better fit.
Q: What tractor HP do I need to run a post hole digger?
A: Ashok Metal Works recommends 45+ PTO HP for heavy implements like augers and pole lifters; if you're pairing it with a pole erector, look for 2000 kg or more of hydraulic lift capacity as well.
Q: How do I calculate cost per hole for my own project?
A: Add your hourly fuel cost and hourly labour cost, then divide by your realistic holes-per-hour for the soil you're working in. The formula holds regardless of region; only the input rates change.
Q: Does hitting a rock void the warranty?
A: The standard 1-year hydraulic warranty covers hydraulic hoses, the control valve, and the hydraulic cylinder, not physical damage like a bent blade or sheared pin from striking a rock, since that isn't a hydraulic component failure.
Q: Hydraulic vs. PTO-driven post hole digger: which is better for tough soil?
A: Hydraulic-drive models with downforce are the recommended choice for rocky or clay-heavy soil, since they can push through resistance that a standard PTO unit relies on tractor torque alone to handle.
Connect With Us
📍 Ashok Metal Works, Jatrapura, behind Ram Leela Maidan, Vidisha, Madhya Pradesh 464001, India
📞 +91 9993054606 (call or WhatsApp)
📷 Instagram: @ashokmetalworkspvt.ltd · Facebook: Ashok Metal Works · LinkedIn: Ashok Metal Works Pvt. Ltd. · YouTube: @AshokMetalWorks_Pvt.Ltd.
Pricing a fencing or pole job and want a straight answer on which drive type fits your soil? Call or WhatsApp the team with your ground conditions and hole count; they've quoted enough of these jobs to tell you in a few minutes what this post can only estimate.



